Top 10 typical forklift mishaps ， forklift procedure must focus on these issues ！.

Don't ignore the forklift at work. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, honk the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After unloading, the fork must be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed doglegs are banned. High-speed sharp turns will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique circumstances.
6. When the forklift is running, it should obey the web traffic rules in the factory and need to maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when stacking or packing. .
8. The height of the load must not block the driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will be fixed and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork suggestion need to not touch other items or objects. The tons needs to be stabilized with marginal back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is forbidden to utilize forks to raise employees to Electric Forklift Truck for Warehouse engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights Stand-on Electric Pallet Stacker and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak must also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they ought to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844